Seat back Protection - PPF for Model 3 / Y - DIY Wrap Club formerly TESBROS

Seat back Protection - PPF for Model 3 / Y

Complete installation guide and support resources for your Seat back Protection - PPF for Model 3 / Y

Read Before You Install

Please review these critical points to ensure a successful installation:

Surface temperature must be between 60-80°F (15-27°C)
Clean and degrease the surface thoroughly before application
Work in a dust-free environment to prevent contamination
Allow 24-48 hours for full adhesion before cleaning
Use proper tools that were provided/li>

1 Surface Preparation

Proper surface preparation is crucial for a successful installation. Clean the area thoroughly with isopropyl alcohol and ensure it's completely dry.

Required Materials:

Isopropyl alcohol (70% or higher)
Microfiber towels
Lint-free cleaning cloth
Slip solution (mix of water and baby shampoo)
Squeegee

2 Video Tutorials

Watch our installation videos starting with the essential Slip & Tack technique, followed by specific installation guides for each component.

Installation Video 1

Installation Guide

Installation Video 2

Installation Guide

Maintenance & Care

Keep your installation looking great for years

Cleaning Instructions

Hand wash with pH-neutral automotive soap
Avoid automatic car washes with brushes
Use soft microfiber towels for drying
Do not use abrasive cleaners or wax

Long-term Care

Park in shade when possible to prevent fading
Apply ceramic coating for added protection
Inspect edges regularly for lifting
Address damage immediately to prevent spreading

Common Issues & Solutions

Tips and Tricks for PPF Installation

Common issues and their solutions for DIY Paint Protection Film installation

⚠️

How to Remove Fingers (Wrinkles) in PPF

Fix wrinkles and stretch marks in your film

What are PPF Fingers? Wrinkles or bubbles that appear during installation when there's either too much or too little stretch in a particular area of the film. This is common with DIY cut-to-panel PPF kits.

Identify the Fingers

Look for areas where the film is not laying flat against the surface. These can appear as raised lines or bubbles.

Stretching Technique

If the fingers are due to insufficient stretch:

✓

Stretch the Film: Carefully lift the PPF around the wrinkled area and stretch it more to fit the panel properly

✓

Use Tack Solution: Spray tack solution under the fingers

✓

Squeegee Method: Use a squeegee along with a microfiber cloth to press down the fingers. Apply firm pressure and work out the wrinkles from the center outward, holding the squeegee in place for a moment to secure the film

Wrapping Around Edges

For fingers that appear when wrapping around edges:

✓

Apply Heat: Use a hair dryer or heat gun to gently heat the wrinkled area. Be cautious not to overheat, as this can damage the film

✓

Press Down: Once heated, carefully press the wrinkle down with your fingers or a squeegee to smooth it out

Video Tutorial: Wrapping Edges & Corners

💧

How to Remove Bubbles in PPF

Eliminate air bubbles during and after installation

During Installation

✓

Overlap Squeegee Strokes: When squeegeeing, use overlapping strokes to ensure no bubbles are left behind

✓

Spray Slip Solution: If you find a bubble, spray slip solution and gently lift the PPF to release the trapped air. Squeegee the film back down, working from the center of the bubble outward

After Installation

✓

Wait and See: Some bubbles may dissipate on their own within 10-14 days

✓

Needle Technique: If bubbles don't disappear, use a diabetic needle to carefully poke the bubble at an angle (avoid pointing directly at the paint). Gently press down on the bubble until it disappears

Video Tutorial: Removing Bubbles

⚠️

How to Deal with Contamination Under PPF

Handle dirt, dust, and debris trapped under the film

Contamination under PPF, such as dirt, dust, or hair, can be problematic if not addressed early.

Ensure Proper Lighting

Good lighting is crucial. Set up multiple lamps in your workspace to catch any contaminants early in the installation process.

Clean the Panel

Before reapplying the film, spray the panel with slip solution and squeegee it clean to remove any remaining dirt or dust.

Lift and Clean Process

If you spot contamination:

✓

Lift the PPF: Carefully lift the film from the panel

✓

Spray Slip Solution: Generously spray slip solution under the lifted PPF to wash away contaminants

✓

Reapply: Once clean, carefully reposition and squeegee the film back into place

Frequently Asked Questions

How long does PPF last?

With proper care, quality PPF can last 5-10 years before needing replacement.

Will PPF yellow over time?

Our premium PPF includes UV protection to prevent yellowing. Proper maintenance extends longevity.

Can I apply ceramic coating over PPF?

Yes! We actually recommend it for enhanced protection and easier cleaning. Wait 7 days after installation.

Does PPF protect against rock chips?

Yes, PPF provides excellent protection against rock chips, bug splatter, and minor scratches.

Need Replacements?

Damaged or defective materials? Request replacement parts.

Request Replacements

Need More Help?

If you're experiencing issues not covered here, our support team is ready to help.

Contact Support

AIR FILTER REPLACEMENT KIT

MUDFLAP PROTECTION

Limited Edition Center Console Wrap

Complete Chrome Delete Kit

Paint Protection Film Kits

Paint Protection Film Kits